 |
|
|
|
            |
|
||||
|
||||
|
||||
03-13-2006, 04:58 PM
|
||||
|
||||
Installation Of Seat Covers
I'm kicking around buying white/ blue or charcoal/ blue seat covers and am wondering what it takes to install the covers. Is it simple or very labor intensive, because w/ a 19mo old and a new born, Roush time is very limited!
 Did get a chance to get her out the other day though! Since bought new in Dec 02' I have under 4400 miles!
__________________
P51A off-road exhaust & updated ROUSH tune  http://www.cardomain.com/ride/574408/3 360R 5,800k, Jack's sig on dash, 380 pcm, 2.8 pulley, MAC CAI, Flowmasters, S3 suspension, MAC c/c plates, Roush short throw 
|
|
03-13-2006, 05:24 PM
|
||||
|
||||
|
i saw on horsepower tv they installed new covers, it was basically unbolting the seat, taking out the clips below and undoing the old cover and reverse the process. looked like a 2hr job each seat. i am sure it'd come with instructions also.
__________________
Jack Roush Classic #8 of 50 
|
|
03-13-2006, 05:34 PM
|
||||
|
||||
|
I will wait to see your results.... I want to do it too!
__________________
 Pipe Hitters Union Creed: "Live extreme, always give one hundred percent and watch your brother's backs."
|
|
03-13-2006, 06:12 PM
|
||||
|
||||
|
This is who i bought mine from, came with foam also, havent installed mine yet but classic soft trim shop wants $400 to install them........http://cgi.ebay.com/ebaymotors/99-04...spagenameZWDVW
__________________
Mike-02 Roush 360R & 93 GT Conv.
|
|
03-13-2006, 06:26 PM
|
||||
|
||||
|
Quote:
__________________
P51A off-road exhaust & updated ROUSH tune http://www.cardomain.com/ride/574408/3 360R 5,800k, Jack's sig on dash, 380 pcm, 2.8 pulley, MAC CAI, Flowmasters, S3 suspension, MAC c/c plates, Roush short throw
|
|
03-13-2006, 07:09 PM
|
||||
|
||||
|
Wow... those are some high quotes... come over to ATL and I'll do them for half that!
 It'll take a while to get them perfect, but it is easy enough for the DIY'er!
__________________
Chris roushstud ROEA A-254  If knowledge is the key, where is the door??
|
|
03-13-2006, 07:12 PM
|
||||
|
||||
|
I took mine to the local Classic Soft Trim shop. They pulled the old seats out, cut the leather and foam off, put the new foam on, put the new leather on and re-installed the seats in about 45 minutes. These guys were flyin'.
I think I paid $200 to have them installed. No problems, couldn't be happier with the seats.
__________________
The gene pool could use a little chlorine.
|
|
03-21-2006, 08:04 PM
|
||||
|
||||
|
Same here on the Classic Soft Trim install. They did a great job and it was worth the price IMO. Here are a few pics...
  
__________________
David 2002 Torch Red 360R Serial # 7145 Dash badge 02-148 (1 of 61 in Torch Red) ROEA Member #77
|
|
03-22-2006, 05:33 AM
|
||||
|
||||
|
Those look SWEET!
 I would like to see a shot of the car w/ the door open to get the whole feel!Anybody else have pics w/ charcoal/ blue and white/blue, that is what I am looking to install!
__________________
P51A off-road exhaust & updated ROUSH tune http://www.cardomain.com/ride/574408/3 360R 5,800k, Jack's sig on dash, 380 pcm, 2.8 pulley, MAC CAI, Flowmasters, S3 suspension, MAC c/c plates, Roush short throw
|
|
03-22-2006, 07:10 AM
|
||||
|
||||
|
I have never seen the white/blue b4...i'm curious just to see it
__________________
 '98 Cobra R.I.P. - 2001 Roush Stage 3
|
|
03-22-2006, 09:42 AM
|
||||
|
||||
|
I have a pic of them, but I would like to see a better shot of them, they are soooooooo sweet!
 
__________________
P51A off-road exhaust & updated ROUSH tune http://www.cardomain.com/ride/574408/3 360R 5,800k, Jack's sig on dash, 380 pcm, 2.8 pulley, MAC CAI, Flowmasters, S3 suspension, MAC c/c plates, Roush short throw
|
|
03-22-2006, 10:44 AM
|
||||
|
||||
|
actually...i'd have to see a better shot...but from that angle..those are hot
__________________
'98 Cobra R.I.P. - 2001 Roush Stage 3
|
|
10-10-2006, 08:02 PM
|
||||
|
||||
|
Rather than start a new thread Ill bring this one back. I just bought these and am thinking about installing them myself. As long I have patience Im sure I can do it in a few hours. Anyone else done it? Any suggestions? One question I have is whats the story on the headrest? The stock foam headrest is a lot smaller than the new cover.
http://cgi.ebay.com/ebaymotors/ws/eB...RK%3AMEWN%3AIT
__________________
|
|
10-10-2006, 08:46 PM
|
||||
|
||||
|
Thats a good buy bud. I would let someone else do it but it cant be too hard with some patience. Check out some other forums and pick some local peeps brains that do it for a living, D
|
|
10-11-2006, 12:32 PM
|
||||
|
||||
|
Quote:
__________________
 Kenne Bell Twin Screw Intercooled Supercharger - 9 PSI pulley (11.5 PSI at the gauge) 440 HP 440 Tq www.svtusa.com
|
 |
| Thread Tools | |
| Display Modes | Rate This Thread |
|
|
Linear Mode
