steering wheel emblem

[dfreezer1]

I think this looks better than the piece of tin tri pony. What do you think?

[xzo6]

Did you get that from,"Making it Digital"? I like the Pony better for the steering wheel in my opinion...In the photo it seems to stick out too far,since you applied it over the original.

[Saint]

If it was recessed more it would be really bad ass! I like it though.

[racione]

Damn, I thought for a second someone had found out how to take the pony off the steering wheel. I've been wanting to put that Roush emblem on there for months.

[dfreezer1]

I took off the tri pony and carved out the raised plastic underneath with an x-acto knife. Its actually flat across not raised. The tri pony is held on by six small pins, very easily removed.

[racione]

I took off the tri pony and carved out the raised plastic underneath with an x-acto knife. Its actually flat across not raised. The tri pony is held on by six small pins, very easily removed.

dfreezer, Are they just plastic pins, and can you just pry it off or how does it come off? Do you have a picture of yours on?

[dfreezer1]

The emblem is tin and the small tabs are at 1 3 5 7 9 and 11 o'clock positions.
The pins are no more than 1/4 inch tabs that stick into the wheel at 90 degrees from the emblem. It's hard not to bend the tri pony during removal so you better have something to replace it with.

[dfreezer1]

This might show how recessed it sits

[redfire427]

Damn, I thought for a second someone had found out how to take the pony off the steering wheel. I've been wanting to put that Roush emblem on there for months.

Dave, did you ring. Hmmmmm, I wonder where you could get one of those.
Could it be on my list of things to make?

[racione]

Dave, did you ring. Hmmmmm, I wonder where you could get one of those.
Could it be on my list of things to make?

Carman, I don't doubt that for a second. Keep up the great work.

[B-NROUSH]

I think it looks sweet....Dont you have to pick what size you want? What size did you go with?

[racione]

The emblem is tin and the small tabs are at 1 3 5 7 9 and 11 o'clock positions.
The pins are no more than 1/4 inch tabs that stick into the wheel at 90 degrees from the emblem. It's hard not to bend the tri pony during removal so you better have something to replace it with.

Hey Thanks dfreezer1, picture looks great. I will try it tomorrow.

[LeeMo]

Hey, I've got to have one. The people that I bought my 05 from had yanked the pony emblem off the steering wheel. All I have is a blank on the wheel. Where do I get one? thanks

[racione]

Hey, I've got to have one. The people that I bought my 05 from had yanked the pony emblem off the steering wheel. All I have is a blank on the wheel. Where do I get one? thanks

Try makingitdigital.com. I think the measurement you need is 2 3/8" but not sure check it to be sure.

[Jus Cruisin]

I like it!!! Don't understand why Roush didn't do that originally.

I did go out and measure and it does look like 2 3/8" is the one that will fit.

Now all I need is to find where to get a matching carbon fiber applique for the passenger air bag "doors".

[WhiskeyRunner]

Really like the looks. Would like one on my fake gas cap to.

[trouble]

I like it!!! Don't understand why Roush didn't do that originally.

I did go out and measure and it does look like 2 3/8" is the one that will fit.

Now all I need is to find where to get a matching carbon fiber applique for the passenger air bag "doors".

heres a pic of mine in the p51

[Rider4Life01]

I gotta say I didnt like it at first.... But i kept looking at it and looking at it.... Its grown on me, I think it looks good... Vey creative bro, Great Mod

[thunderstruck]

I like it!!! Don't understand why Roush didn't do that originally.

I did go out and measure and it does look like 2 3/8" is the one that will fit.

Now all I need is to find where to get a matching carbon fiber applique for the passenger air bag "doors".

Roush Carbon Fiber Air Bag

[metz]

I def want to do this. What size did you get Dfreezer1?